-
Boot Seals external Weatherproof Pipe Seals for pipe not centered Pipe-Seals external mount units Pipe-Seals external wall mount Pipe Seals- multi pipe penetrations Pipe Seals water hammer isolation Seals differential settlement Pipe Seals & waterproof liner seal Pipe Seals for vibration damping Pipe Sealing for metal tank walls Pipe Seals for axial movement-NS Pipe Seals through floor slabs End Seals casing pipes Pipe Plug Seals taper fit Manhole Seals joint jnflow Pipe Seal Boots Septic Tanks Connector Boots pipe to manhole Pipe Seals Weatherproof Split Boot Pipe Seals hi-temp silicone rubber Pipe Sealing Internal repair
Wall Sleeves for Large Pipes Wall Sleeves External Wall Wall Sleeves Split For Existing Pipes Wall Sleeves Split Boot Weatherproof Wall Sleeves Flange Connect Wall Sleeves Puddle Flange Wall Sleeves Tank Connection Wall Sleeves Multi-Conduit entry Wall Sleeves Tempoary Entry
- END SEALS
Repair Clamp Split Bolted Repair Clamps Flange Leak Repair Clamps Pit Hole Leaks Repair Clamps Encapsulating Repair Clamps Pipe Bends Repair Pipe Leak Inside
Restraint Coupling Couplings HDPE & PVC Pipes Couplings PVC to Steel Pipe Couplings Stainless Housing Repair Couplings different size pipes High Pressure Pipe Couplings
Pipe Plugs Pneumatic Pipe Plug sectional large pipes Pipe Plugs Mechanical Packers Pipe Repair Internal
Heated Wraps TOTES Heated Wraps DRUMS Heated Wraps PUMPS Heated Wraps TANKS Heated Tarps CONCRETE Heated Wraps PIPES Drum Ovens 4 Barrel Heaters
BUILDING ENTRY PIPE SEALS
PUDDLE FLANGE EDPM PIPE SEALS
SEAL PIPES FROM OUTSIDE WALL
MANWAY HATCH COVERS
FLANGE ISOLATION KITS
MONOLITHIC ISOLATION JOINTS
Flange Isolation Kits For Cathodic Protection
Flange isolation kits: are available for all flange sizes, types, pressure ratings and materials.
INTRODUCTION: Flange Insulation Gasket Kits prevent electrical conductivity between the flanges.
The kit consists of one Insulating Gasket, one full length insulating sleeve per bolt, two insulating washer per bolt and two metal washer per bolt.
Isolation gaskets are commonly used as an insulator between dissimilar metal flanges for corrosion protection.
Insulating kits isolate electrically pipe sections in cathodic protection systems, to prevent the flow of stray current along the pipelines.
Flange Insulation Gasket Kits are designed to prevent electrical conductivity between the flanges.
Isolating gaskets are suitable for use in Full Face, IBC and RTJ flanges. WA Isolation kits have excellent dielectric properties and superior sealing characteristics. The gasket is suitable for all pressure ratings including ASME B16.5, ASME B16.47, API 6B and API 6BX flanges up to 20,000 PSI
Contact Westatlantic 902 455 4455 or email your requirements for pricing on all flange sizing and conditions.
RAISED FACE GASKET – WA-TYPE F flange gaskets
Type "F" raised face gaskets are placed inside the flange bolt circle and seats fully on the raised face of the flange.
Raised face flange type of gaskets are supplied in all the materials, Phenolic and Glass / Epoxy with Neoprene Rubber coating.
Cut sheet Flange Isolation Kits:
FULL FACE GASKET – WA-TYPE E
Type "E" full face isolation gasket seats with it's outside diameter equal to that of flange OD. The bolts run through the gasket.
INSULATION Gaskets – WA-Very Credical high pressure conditions
High Pressure flange isolation Gaskets: designed for very critical service.
HIGH PRESSURE INSULATION SEAL – WA-RTJ FLANGES
The gasket is suitable for use in Full Face, IBC and RTJ flanges. Excellent dielectric properties and superior sealing characteristics.
Critical isolation gaskets are suitable for all pressure ratings including ASME B16.5, ASME B16.47, API 6B and API 6BX flanges up to 20,000 psi.
Phenolic materials are available on request for low temperature and low pressure services.
High tensile fasteners are available with insulation kit gasket on request with or without Hot Dip Galvanized.
All Standards And Non Standard Dimensions of Insulation Kit Gasket are Available.
Very Critival Fire safe Isolation Kits
FIRE SAFE INSULATION GASKETS
Fire safe Gasket Kits are designed for preventing leakage of process fluid and provide insulation during fire.
Insulation Gasket kits have spring energized PTFE seal and an E ring with special high temperature Xylar coating.
Firesafe High Pressure seal with Kamprofile
Isolation Gasket PTFE laminated Stainless Steel core with Spring energized PTFE seal and high temperature insulation coated Kammprofile with Mica Sheathing. Metal washers are with high temperature insulation coated
ASME/ANSI B16.5 / 150 to 600 PSI / 0.5" to 24"
ASME B16.47 series A & Series B / 150 to 600 PSI / 26" to 60"
ASME B16.5 / 900 to 2500 PSI / 0.5" to 24"
API 6B & 6BX / 720 to 20000 PSI / 1.5" to 30"
Non-Standard / All types and sizes
Download Flange Isolation Gaskets Brochure:
Contact us: Westatlantic Tech Corp, 902 455 4455